Oscilloscope News

Keysight-N2804A12 November 2014 – Keysight Technologies introduced 200-, 300- and 500-MHz, high-voltage probing solutions with a wider input range, higher common-mode rejection ratio and optimized accessories. The probes are ideal for testing today’s switching power supplies or power devices and for measuring motor drives and vehicle buses. The Keysight N2804A differential probe offers up to 300-MHz bandwidth and ±300-Vdc + peak AC of the maximum differential input range, allowing engineers to use it for a broad range of power applications.

TLEC LabMaster111 November 2014 - Teledyne LeCroy introduces the LabMaster 10-100Zi featuring a real-time bandwidth of 100 GHz and a sample rate of 240 GS/s. The 100 GHz technology was first publicly demonstrated in July 2013, and has since been featured at the 2014 DesignCon, OFC and ECOC exhibitions. The technology included in the LabMaster 10-100Zi is key to analyzing and understanding the fastest phenomena found in R&D of next-generation communication systems, high bandwidth electrical components, and fundamental scientific research.

RS-RTM11 November 2014 - Equipped with the R&S RTM-K15 history and segmented memory option, the R&S RTM bench oscilloscope enables users to analyze longer signal sequences than is possible with any other instrument in this class. The R&S RTM automatically acquires only the relevant signal sequences, such as bursts or pulses, and stores them in segmented memory. The oscilloscope's full functionality can then be used to analyze the acquired signals in detail.

BitScope Micro and Raspberry Pi 207 November 2014 - element14 has partnered with BitScope Designs to manufacture and distribute BitScope Micro, a full feature dual channel digital oscilloscope for Raspberry Pi. BitScope Micro is also an eight channel logic analyser, waveform generator, clock generator and spectrum analyser all packaged in one low cost lightweight water resistant test probe. BitScope Micro captures digital signals at up to 40 MSps and has a 20 MHz analogue bandwidth.

RS-RTE07 November 2014 - With the high definition (HD) mode Rohde & Schwarz increases the vertical resolution of the R&S RTO and R&S RTE oscilloscopes to up to 16 bits - a 256-fold improvement over 8-bit resolution. Waveforms are sharper and show signal details that would otherwise be masked by noise. Users benefit from even more precise analysis results.

Keysight-N2804A05 November 2014 – Keysight Technologies introduced 200-, 300- and 500-MHz, high-voltage probing solutions with a wider input range, higher common-mode rejection ratio and optimized accessories. The probes are ideal for testing today’s switching power supplies or power devices and for measuring motor drives and vehicle buses.

PicoScope-934122 October 2014 - With the new PicoScope 9341 20 GHz Sampling Oscilloscope, engineers can analyze two differential or four single-ended high-speed signals. The instrument is ideal for measuring skew and crosstalk between differential pairs on serial buses such as HDMI, SATA and PCIe, and for testing signal integrity at differential and single-ended transceiver ports. Data rates up to 40 Gb/s can be viewed, with 5th-harmonic characterization possible up to 8 Gb/s.

Pico-8-Channel15 October 2014 - The new PicoScope 3000D Series Mixed-Signal Oscilloscopes (MSOs) form a complete portable test system, with two or four analog channels and sixteen digital channels as well as a built-in arbitrary waveform generator. The PicoScope 3000D Series MSOs are available with analog bandwidths from 60 MHz to 200 MHz. Maximum digital input frequency is 100 MHz, equivalent to a data rate of 200 Mb/s (5 ns pulse width) on each channel.

TLC-Wavesurver10a14 October 2014 - Teledyne LeCroy introduced the WaveSurfer 10 oscilloscope with 1 GHz and 10 GS/s at €9,990/£8,640. The WaveSurfer 10 combines the MAUI advanced user interface with powerful waveform processing, in addition to advanced math, measurement and debug tools, to quickly analyze and find the root cause of problems.

RS-RTO-osci10 October 2014 - Developing USB-capable devices and integrating their interfaces requires reliable, fast and easy-to-operate test solutions. The R&S RTO-K60 triggering and decoding option addresses this need for USB 1.0/1.1 and 2.0 as well as for the high-speed interchip (HSIC) version. This option together with the R&S RTO-K21 compliance test software and the R&S RTO-ZF1 test fixture set from Rohde & Schwarz is the ideal tool for developers who have to integrate USB interfaces.

Related Articles:

No related articles found


 

 Advertising